Pocket worthyStories to fuel your mind

How To Replace Brake Pads

This DIY job is a little more complicated than changing a tire, but it’s totally doable at home with the proper parts and tools.

The Drive

Read when you’ve got time to spare.

Brake pad

Like an oil change, replacing your car’s brake pads is a do-it-yourselfer’s rite of passage—the next scout badge, the hard-earned promotion, the leveling up of a wrencher. But not everyone has an Uncle Jonathon or a weird neighbor Peter to help them get to that next step and explain how to replace brake pads... until now.

Changing your car’s brake pads is an often overlooked piece of car maintenance. They’re sort of the “Set it and forget it!” of automotive systems. They’re not really a part you regularly check. Yet, your brakes are perhaps the most important part of your car as they ensure your continued survival. Maintaining them, then, should be a top priority and one of the easiest ways to do that is by replacing your brake pads when they start to fade. 

Everything You’ll Need to Replace Brake Pads

In terms of skill required, this job falls somewhere between easy and intermediate. You should set aside up to two to four hours, but the actual time it’ll take will vary from vehicle to vehicle. 

Safety First
Tools and Parts

Here’s How To Replace Brake Pads, Step by Step

Step 1: Loosen Lug Nuts

Grab a tire iron or an impact wrench and loosen the lug nuts on the front two wheels.

Step 2: Lift the Car

For clearance, raise the vehicle with a floor jack or a full hydraulic lift—whatever you have handy.

IMG_1335-scaled.jpg
Step 3: Place Jack Stands

Be mindful of where you set the jack stands, preferably on the frame. Don’t set place them on the rocker panel or any of the bodywork that would crumple from the weight of the car.

Step 4: Remove Wheel

Store it out of the way so you have clear access to the hub.

Step 5: Locate and Remove Mounting Bolts

They’ll be at the rear of the caliper. Once you’ve taken them off, store them in a baggy so you don’t lose any.

IMG_4514-scaled.jpg

A close-up of the brake pad sitting against the brake rotor. (Peter Nelson)

Step 6: Remove Anti-Rattle Clip

You can pry it with a flathead screwdriver but it may fly off, so be careful. This is where those safety glasses may come in handy.

Step 7: Remove Caliper

You can now slide the caliper off the rotor. Rest the caliper on the top rotor (or hang it with a hook) so it’s not hanging by the weight of the brake line.

IMG_1337-scaled.jpg
Step 8: Remove Pads

With the caliper free, take off the brake pads. Inspect for uneven wear to ensure everything is properly lined up and there’s no debris caught inside.

IMG_1336-scaled.jpg
Step 9: Place Pliers on Piston

The brake caliper piston, the piece that pushes the brake pad into the rotor, may be extended. Using face clamp pliers, put one side of the plier’s grip on the piston and the other side on the caliper’s steel backing.

Step 10: Press Piston Into the Caliper Until It Sits Flush

Be sure not to damage the piston’s rubber. 

Step 11: Lubricate Inboard Pad

Take the inboard brake pad, the one with a retaining clip on its backing, and place a small amount of brake pad lubricant on the back of it.

Step 12: Lock Piston

Press into the piston’s opening until it locks in place.

Step 13: Lubricate Outboard Pad

Take the outboard brake pad and place a small amount of brake pad lubricant on the back of it.

Step 14: Rest Brake Pad

Rest the outboard brake pad on the caliper mounting bracket that’s still attached to the rotor.

Step 15: Insert Outboard Brake Pad

Slide the caliper with the outboard brake pad attached back onto the mounting bracket with the outboard brake caliper.

Step 16: Lubricate Mounting Bolts

Grease the caliper’s bolts, but not the threads, and reinstall them.

Step 17: Reattach Anti-Rattle Clip
brakes.jpg
Step 18: Repeat

Complete this process at every corner that needs new brake pads.

Step 19: Reattach Wheels

Hand-tighten the lug nuts for now.

Step 20: Remove Jack Stands

Raise the jack enough to remove the stands. Be extremely careful not to bump the jack while under the car.

Step 21: Lower Car

If you’re using a floor jack, twist the handle slowly to the left.

Step 22: Torque Lug Nuts

Torque the lug nuts to their manufacturer’s designated specification.

Step 23: Locate and Remove Brake Fluid Cap

Pop the car’s hood and remove the brake fluid cap, which will likely have the letters “DOT” in big letters.

Step 24: Pump Brakes

Press the pedal repeatedly to make sure braking pressure has returned and the air is out of the system. Then put the brake fluid cap back on and close the hood.

Step 25: You’re Done

If there’s no air left in the system, you’re done!

How was it? Save stories you love and never lose them.


Logo for The Drive

This post originally appeared on The Drive and was published October 30, 2023. This article is republished here with permission.

Want to get more stories like this in your inbox?

Join TheDrive’s newsletter